Woodfinishers Weblog

Wood finishing forum for professional finishers

Back painting glass using the CIC Mustang adhesion promoter

Adhesion promoters are a very useful tool to have in your belt as a finisher, as you will see in this very informative video by master finisher and good friend Thomas Craven, of Thomas Craven studios in Van Nuys California.

Back painting glass is what we are doing here, the other uses for this product are where you have to paint  rubber or plastic, this product was originally designed for painting plastic bumpers  and parts for the automotive industry ( Rubber bumpers on cars, 30 years ago that was a joke). Another use is painting over plastic laminates. I had a customer that bought some very expensive custom cabinet doors from Italy, they were a laminate that had a custom wave C-N-Ced in to the door, the customer made a mistake and got the wrong color,  we used the adhesion promoter on these and fixed the color.

Tom is using the CIC mustang adhesion promoter to back paint glass that is going to be used as a black splash, this is a cool little technique and is very popular. It has high tech ultra modern look and is easy to do, getting the paint to stick to the Glass is the tricky part.

An adhesion promoter is in essence a spray on glue that bonds to the glass and then bonds to your paint and thereby promoting adhesion, Simple Right?    yes and no.

There are a few key application points that Tom goes over in the video that are very Key, two light  (underline) coats. this is not a coating in itself you just want enough to get so stick.

NEXT POINT, you apply  your paint while the adhesion promoter is still tackie. don’t let it dry and then paint over it you have defeated the purpose.

The CIC mustang is a great product as it sprays out very light and doesn’t clump or clog, when looking at the glass you wouldn’t know that there was anything other than the color coat, and guess what you can get that product and other fine CIC products on my web site at http://www.annexpaint.com. if  you have questions you are welcome to write to me at info@annexpaint.com.

and here’s the video:

 

best,

Greg Saunders

 

February 2, 2015 Posted by | Conversion varnish, Spray techniques, Tips and Tricks | , , , , , , | Leave a comment

Is Rexcel Water based conversion coating flammable ?

I had a contractor ask  me the question is the conversion coating flammable as he was going to finish a wine cellar in a basement where there was a gas burning furnace. Normally when spraying lacquers on a job site you want to make sure that all open flames are extinguished Vapors sometimes being heaver then air can sprayed along the ground to a gas burning water heater and go boom –not good. Matt the contractor wanted to find a water based material that would not have this problem and was interested in the Rexcel conversion coating  the following is my response …

“The materials are not flammable However, they are potentially combustible, you should always spray in an area that is properly ventilated and I would, if at all possible turn off the furnace while spraying. Inert dust, such as saw dust or even flower can become explosive all by itself if there is a sufficient quantity of in suspended in the air. Like wise with a sealed room full of over spray and vapor.

The Rexcel conversion coating is water based but it does have volatile chemicals in it.  If for some reason you can’t turn off the furnace then ventilate the room so that your fumes are being sucked out of the room and not into the furnace.”

All that being said I doubt you would have a problem, but I don’t want to be the on that gets you blown up. What I have done personally in the past when confronted with such situations is to erect a temporary spay booth around the work with Plastic and 2X2s or something similar. Tape it to the ceiling and floor, Home depot sells zippers that you can tape on to the plastic and use as an entry and exit.  Then I would duct in (either with plastic or flex dusting you can also find at home depot) and air supply and an exhaust, I have built some pretty spiffy spray booths in some real swanky homes where the customers did not want to spell lacquers. You can put a A/C air filter on the exhaust side to catch particles before it goes out a window.   

 Let me know if that is helpful.

Greg Saunders

ANNEX PAINT

November 12, 2009 Posted by | CIC Centurion, water based Conversion Varnish, Conversion varnish, Tips and Tricks, Water based Lacquers | , , , , , | 1 Comment